GMT+8 · Reply within 12 hours
Haoze logo Shandong Haoze Suspension PVC Resin
Get a Quote
Quality2026-09-246 min read

How to Read a PVC Resin Bag: Standards, Grades and Markings

A practical guide to PVC resin packaging: GB/T 5761-2018 vs enterprise standards, why S-700 and SG-5 are different systems, and net weight tolerances.

阅读中文版 →

Читать на русском →

An order for PVC resin names one thing. The bags that arrive often name something slightly different: a different grade name, a different standard number, a net weight written three different ways. For a buyer receiving a first shipment from a new supplier, this is where most of the uncertainty sits.

This article sets out what is actually printed on a PVC resin bag, what each line means, and which differences are routine versus which ones deserve a question before the delivery note is signed.

Everything below is industry-standard marking practice. The photographs show real bags from stock, for comparison with what a buyer receives.

1. The standard line: GB/T 5761-2018 is not the only valid answer

The single most common source of confusion. Buyers often assume a bag without "GB/T 5761" on it is substandard. That assumption is incorrect.

Marking What it is Is it acceptable?
GB/T 5761-2018National standard for suspension PVC resin, current versionYes, the baseline
GB/T 5761-2006The previous national standard versionYes, if the resin was produced under it
Q/SH3160.77-2016 / -2019Enterprise standard (企标), used by large producers whose internal specs are tighter than the national baselineYes, often stricter
Q/TWPVC 001-2017Enterprise standard for a specialty grade (e.g. matte/消光 resin)Yes, no national standard exists for that grade
A bag marked with an enterprise standard rather than GB/T 5761
Enterprise standard, not national. This bag carries Q/SH3160.77-2016, a producer standard. Large producers write their own because their internal control on viscosity and impurity is tighter than the national floor. This is not a downgrade.

The practical rule: a standard line tells which specification the batch was tested against. It says nothing about how good the resin is. What matters is that the standard on the bag matches the standard on the COA that was sent. If the bag says Q/SH3160.77-2019 and the COA says GB/T 5761-2018, the discrepancy should be queried. One of the two documents is describing a different batch.

2. The grade line: S-700 and SG-5 are two naming systems, not two products

This trips up experienced buyers too. Two numbering conventions coexist in the Chinese PVC market:

System Example Who uses it Maps to
National grade codeSG-5Most producers; the GB/T 5761 conventionThe "5" indicates the K-value / degree of polymerization band
Producer model numberS-700, S-1000, S-1300Several large state-owned producersAn internal model line. The number is not the SG grade

The trap: S-700 and SG-7 are not the same thing. The number in an S-series model is a producer-internal designator. Two different producers can both sell "S-700" and the resins may differ.

Three bags from the same producer model line
One model line, three specifications. Here S-1300, the highest of the series. The progression S-700 → S-1000 → S-1300 tracks rising molecular weight, which means higher viscosity and different end uses. None of these numbers is an SG grade.

How to avoid the mismatch: when an offer quotes S-1000, the buyer should request three things in writing — the equivalent SG range, the K-value, and the application the resin is intended for. A supplier unable to answer is reselling without understanding the product.

3. Net weight: three ways of writing the same 25 kg

Legitimate bags carry all of these:

Printed as Meaning
净含量: 25kgNominal 25 kg
净含量: 25.0kg ± 0.2kg25 kg with a stated filling tolerance (the honest version)
NET WT: 25kgEnglish equivalent
净重: 1000KGThis is a jumbo bag, not a 25 kg sack

A bag printed 25.0kg ± 0.2kg is not a warning sign. It is the more precise declaration. It tells the buyer that the filler's equipment is calibrated and the producer is willing to state the tolerance. A bag with no tolerance stated at all is worth more suspicion than one that states ±0.2 kg.

Specialty grade bag with QR code and stated tolerance
A conventionally marked SG-5 bag. Note the grade line (SG-5), the national standard (GB/T 5761-2018), and the net weight. This is the most common layout in the SG series.

4. Mercury-free and PVC-FREE markings: what they are actually claiming

Some bags carry a Hg-FREE or PVC-FREE mark. These mean different things and buyers frequently conflate them:

  • Hg-FREE (无汞): the resin was produced using a mercury-free catalyst in the VCM process. Relevant if a buyer exports to markets with mercury-restriction procurement rules. This is a process claim.
  • PVC-FREE on a PVC bag: reads as contradictory, but on packaging it usually refers to the ink or the bag liner being PVC-free, or to a grade intended for food-contact applications where the additive package avoids certain phthalates. If the mark appears and it matters for the end use, written clarification should be requested.
Bags marked with an additive claim
Additive claims printed on the bag line. A mercury-free catalyst claim is a process statement about how the VCM was made. It says nothing about the K-value or the grade. It is not on its own a quality indicator.

5. Jumbo bags: the same resin, a different handling decision

At roughly one tonne per bag, jumbo bags (FIBC / 吨袋) are a logistics decision; the resin inside is the same. Whether an order is placed in 25 kg sacks or jumbo bags depends on the unloading and feeding equipment available on site.

One-tonne jumbo bags staged on pallets
Jumbo bags, staged on pallets. Same resin as the 25 kg sacks, roughly forty times the unit weight. These suit a site that has the forklift and hopper to handle them. The bag has lifting loops, not a hand-carry format.

The trade-off is straightforward:

25 kg sacks Jumbo bags (~1 t)
HandlingManual, no equipment neededRequires forklift + lifting frame
Unit costHigher per tonne (packaging)Lower per tonne
Resin lossLower, open one sack at a timeHigher, once opened, the whole tonne is exposed
Best forSmall plants, mixed grades, sample ordersHigh-volume single-grade lines

6. What a full batch of stock actually looks like

Stock conditions matter more than most buyers expect, because PVC resin is hygroscopic. A bag that has sat in a damp corner will cause problems in the extruder that no COA will predict.

Palletised PVC resin stock in a warehouse
Palletised stock on raised pallets. Note the blue pallets keeping every bag off the concrete floor. This is the single most important storage detail for PVC resin. Bags sitting directly on a damp floor will draw moisture through the paper layer.

Two things to check on a physical inspection, both visible in this photograph:

  1. Pallets under everything. Concrete floors transfer moisture. Bags stacked directly on the floor are the most common cause of downstream complaints that the resin felt different.
  2. No wall contact. A second photograph shows the same principle from the side, stock held clear of the wall, with air able to move.
PVC resin bags stacked clear of the wall
Stacked clear of the wall. The gap matters. It stops condensation from forming on the wall face and migrating into the paper sacks. On a stock inspection, walking the perimeter and looking for bags pressed flat against a damp wall is worthwhile.

7. The five-line check

Before a delivery note is signed, these five lines should sit side by side with the purchase order:

  1. Grade or model: and if it is an S-series model, the equivalent SG range in writing
  2. Standard number: and whether the COA on file states the same one
  3. Net weight: nominal or with tolerance; jumbo bags check the tonne figure
  4. Batch / lot number: must match the COA that was sent
  5. Additive claims (mercury-free, PVC-free, food-contact) relevant only if the end market requires it

If all five line up, the paperwork and the physical goods agree. If one does not, the question should be raised the same day, before the containers are unstuffed.


A note on where these photographs came from

Every image above is a real bag from stock, photographed as received. The producer markings were deliberately left visible. The point of this article is that the markings are readable by the buyer, on whatever bags arrive, from whichever supplier.

When a buyer needs to know which grade suits an application, the relevant K-value or SG range, end product and quantity can be sent to the supplier, who returns the specific model number and a firm offer.

Each grade has its own page with the GB/T band, the COA items to check and what buyers use it for: SG-3, SG-5, SG-7, SG-8.

The supplier behind those markings, and the checks agreed before dispatch, are listed on the Haoze cooperation page.

SG-5 for the next production run

The grade, the tonnage and the destination port produce a price, a specification sheet and the full document list, usually within 12 hours (GMT+8).

WhatsApp